| 8” FRPV Membrane Housings | ||||||
|---|---|---|---|---|---|---|
| Elements | Part Number | Maximum Operating Pressure | Maximum Operating Temperature | Minimum Operating Temperature | Inlet Port | Permeate Port |
| 1 | FRPV-8030S-1F | 300 psi (21 bar) | 150° F (66° C) | 14° F (-10° C) | <1.5” | 1” |
| 2 | FRPV-8030S-2F | 300 psi (21 bar) | 150° F (66° C) | 14° F (-10° C) | <1.5” | 1” |
| 3 | FRPV-8030S-3F | 300 psi (21 bar) | 150° F (66° C) | 14° F (-10° C) | <1.5” | 1” |
| 1 | FRPV-8060S-1F | 600 psi (41 bar) | 150° F (66° C) | 14° F (-10° C) | <1.5” | 1” |
| 2 | FRPV-8060S-2F | 600 psi (41 bar) | 150° F (66° C) | 14° F (-10° C) | <1.5” | 1” |
| 3 | FRPV-8060S-3F | 600 psi (41 bar) | 150° F (66° C) | 14° F (-10° C) | <1.5” | 1” |
INTENDED USE
Hydron FRPV Membrane Housings are designed for continuous, long-term use a as a housing for single and multiple reverse osmosis and ultrafiltration elements in typical commercial water treatment systems at pressures from 300 psi – 600 psi.
Hydron FRPV Membrane Housings must be installed, operated and maintained in accordance with the listed precautions, and good industrial practice to assure safe operation over a long service life.
The high performance reinforced plastic shell must be allowed to expand under pressure; undue restraint at support points or piping connections can cause leaks to develop in the shell.
The end closure, incorporating close-fitting, interlocking metal components, must be kept dry and free of corrosion; deterioration can lead to catastrophic mechanical failure of the head assembly.
PRECAUTIONS
DO… read, understand and follow all instructions; failure to take every precaution will void warranty and may result in vessel failure.
DO… inspect end closures regularly; replace components that have deteriorated and correct causes of corrosion.
DO… provide overpressure protection for vessel set at not more than 105% of design pressure.
DO… mount shell on horizontal or vertical members at central span “S” using compliant, vessel supports; tighten hold down straps just snug.
DO NOT… pressurize vessel until double checking to verify that the retaining rings are in place.
DO NOT… work on any component until first verifying that pressure is relieved from vessel.
DO NOT… tolerate leaks or allow end closures to be routinely wetted in any way.
DO NOT… operate vessel with permeate pressure in excess of 125 psi at 120 °F (0.86 MPa at 49°C).
DO NOT… make rigid piping connections to parts or clamp vessel in any way that restricts growth of fiberglass shell under pressure; DIA = 0.01 in. (0.25 mm) and L = 0.3 in. (.8 mm) for a length code -1 vessel .
DO NOT… hang piping manifolds from parts or use vessel in any way to support other components.
DO NOT… operate at pH levels below 3 or above 11.
DO NOT… operate vessel at pressures and temperatures in excess of its rating.
| 8” FRPV Membrane Housing Measurements | ||||
|---|---|---|---|---|
| Elements | Part Number | A | B | C |
| in (mm) | in (mm) | in (mm) | ||
| 1 | FRPV-8030S-1F | 58.82”+ 0.12” (1494 + 3) | Ø9.49”+ 0.07” (Ø241 + 2) | Ø8.27”+ 0.12” (Ø210 + 3) |
| 2 | FRPV-8030S-2F | 98.82”+ 0.12” (2510 + 3) | Ø9.49”+ 0.07” (Ø241 + 2) | Ø8.27”+ 0.12” (Ø210 + 3) |
| 3 | FRPV-8030S-3F | 138.82”+ 0.12” (3526 + 3) | Ø9.49”+ 0.07” (Ø241 + 2) | Ø8.27”+ 0.12” (Ø210 + 3) |
| 1 | FRPV-8060S-1F | 62.28”+ 0.12” (1582 + 3) | Ø9.96”+ 0.07” (Ø253 + 2) | Ø8.58”+ 0.12” (Ø218 + 3) |
| 2 | FRPV-8060S-2F | 102.28”+ 0.12” (2598 + 3) | Ø9.96”+ 0.07” (Ø253 + 2) | Ø8.58”+ 0.12” (Ø218 + 3) |
| 3 | FRPV-8060S-3F | 142.28”+ 0.12” (3614 + 3) | Ø9.96”+ 0.07” (Ø253 + 2) | Ø8.58”+ 0.12” (Ø218 + 3) |
